Completed Custom Built Bobbin Wound Inductor designed to operate in control circuit.
- Inductance: 10mH, +/-10% @20 Amps
- Hi-Pot Test: 1,500Vac to core
- Core Structure: E-I lamination, SiFe, Interleaved
- Dimensions: 2″H x 2-5/16″W x 1-7/16″D
- Hole Spacing: 2-9/16″ center to center x 3/16″ holes
- Terminations: 1/4″ Faston
- Mounting: Channel Frame
- Finish: Varnish coated
- Weight: Approximately 1 pound
- Part Number: 120-0022
Completed Custom Built Bobbin Wound Inductor designed for current surge suppressor in PWM servo drive.
- Inductance: 200 uHy
- Core Structure: E-E SiFe butt-stacked lamination with approximately 0.010″ – 0.015″ gap
- Dimensions: 3/4″H x 1″W x 1-1/8″D
- Finish: Varnish coated
- Weight: Approximately 0.5 pound
- Part Number: 120-0056
Completed Custom Built Bobbin Wound Inductor designed for avionics test application.
- Inductance: 98mHy @ 456mA
- Frequency: 400Hz.
- Hi-Pot Test: 1,000 Vac to core
- Core Structure: E-I lamination, SiFe, Butt-stacked. approximately 0.005″ gap
- Dimensions: 1-3/8″H x 1-5/8″W x 1-1/8″D
- Hole Spacing: 2″ center to center x 3/16″ holes
- Mounting: Channel Frame
- Finish: Varnish coated
- Weight: Approximately 0.5 pound
- Part Number: 120-0092
Completed Custom Built Bobbin Wound Inductor designed for Solenoid test load coil circuit.
- Inductance: 600 uHy @ 18 Amps
- Hi-Pot Test: 500 Vac to core
- Core Structure: E-I lamination, SiFe, Interleaved
- Dimensions: 2-5/8″H x 3-1/8″W x 2-3/8″D
- Hole Spacing: 3-9/16″ center to center x 3/16″ holes
- Termination: 2 x #13 AWG magnet wire, each lead
- Mounting: Channel Frame
- Finish: Varnish coated
- Weight: Approximately 2.5 pound
- Part Number: 120-0103
Completed Custom Built Bobbin Wound Inductor designed for common mode line filter.
- Inductance: 10,000 uHy @ 10A max.
- Hi-Pot Test: 1,800 Vac, Winding to Winding
- Frequency: 47Hz – 63Hz
- Core Structure: Ferrite E-Core
- Dimensions: 1.80″H x 1.20″W x 1.10″D
- Lead Spacing: 1″ x 0.6″ x 0.040″ diameter pins
- Mounting: Thru Hole
- Finish: Varnish Coated
- Weight: Approximately 0.5 pound
- Part Number: 130-0031
Completed custom built bobbin wound inductor designed for a 208Vac, 1-phase line reactor – wound with copper foil. The copper foil used is 0.030″ x 3″ wide. This bobbin wound inductor is designed to function as a 208 volt line reactor.
- Inductance: 75uHy
- Frequency: 60Hz
- Hi-Pot Test: 2,000Vac coil to frame
- Core Structure: 1″ x 0.011″ strip wound core
- Dimensions: 5.5″L x 7″H x 3″W
- Termination: 1-1/4″ x 5/8″ x 1/8″ thick tabs with 5/16″ holes
- Mounting Hole Spacing: 5″ x 2.5″ center to center
- Mounting: Chasis mount, 4 x 5/16″ diameter holes
- Finish: Varnish coated (coils only), for field adjustment of gap
- Weight: Approximately 12 pounds
- Part Number: 120-0080
